-
1X; TRANSMISSION AND DIFFERENTIAL - complete (When stock is exhausted, order D29500)@@D23400 and D25500 transmission also includes items listed on Figures 60 and 62.
-
1X; TRANSMISSION AND DIFFERENTIAL - complete (See D23400)@@D23400 and D25500 transmission also includes items listed on Figures 60 and 62.
-
11RODAMIENTO DE BOLAS; CASE - transmission (Includes ref. #26) D23400 transmission (Has recess in faced surface) use D32570 (See 32369 and D29309)
-
1A1X; CASE - transmission (Includes ref. #2, #3, #4, #26, and #46) D29500 transmission (Has solid faced surface) See D23400, 32369, D27642 and D29309
-
21TAPÓN Sq Hd, 1''-11 1/2 NPTF; - pipe, transmission filler (1'' NPT square head)
-
31X; PLUG - pipe, oil level (1/2'' NPT extended square head)
-
42X; PLUG - pipe, magnetic (Drain)
-
51CUP ASSY.; CUP - oil, main shaft rear bearing
-
61COJINETE RODILLO CÓNICO; SNAP RING - main shaft rear bearing
-
71TAZA; - bearing
-
81X; CONE - bearing
-
91PIÑÓN; GEAR - main shaft, low and reverse
-
101SIN SERVICIO; - main shaft gear
-
111ENGRANAJE; - main shaft, second speed
-
121ENGRANAJE; - main shaft, contant mesh
-
131X; SNAP RING - main shaft front bearing
-
141X; CONE - bearing
-
151TAZA; - bearing
-
161EJE PRINCIPAL;
-
171JUNTA; - main shaft front bearing cap
-
18UARSUPLEMENTO; - main shaft front bearing cap (.005'' thick)
-
19UARSUPLEMENTO; - main shaft front bearing cap (.010'' thick)
-
UARSUPLEMENTO .020'' Thk; Main shaft front bearing cap (Not shown) .020'' Thk
-
201X; CAP - main shaft front bearing
-
211OIL RESERVOIR; SEAL - oil, bearing cap
-
223TAPÓN; HHCS AND LOCKWASHER - 3/8'' - 16 NC x 1''
-
231GEAR WHEEL; COUNTERSHAFT AND BEVEL PINION - (Included with differential)
-
241COJINETE DE RODILLOS; CONE - bearing
-
251COJINETE 3.375'' OD x 0.9375''; CUP - bearing
-
261ANILLO DE RESORTE; SNAP RING - countershaft rear bearing
-
271SIN SERVICIO; - countershaft, first and reverse
-
281ENGRANAJE; - sliding, second and third
-
291ENGRANAJE; AND BUSHING - third
-
301CASQUILLO; - countershaft third gear
-
311ANILLO DE RESORTE #250, 2.673'', Int; - countershaft front bearing
-
321ARANDELA BELLEVILLE; - retaining, countershaft third gear
-
331X; WASHER - spring, countershaft third gear retaining (use D11205)
-
1KIT DE COMPENSADOR; KIT - shim pack, countershaft third gear retaining
-
331SEPARADOR; WASHER - spacer, hardened (1-1/32'' I.D. x 1-7/16'' O.D. x 3/64'' thick)
-
33A2SUPLEMENTO .004'' Thk; Steel (Not shown) .004'' Thk
-
33B2SUPLEMENTO .007'' Thk; Steel (Not shown) .007'' Thk
-
33C5SUPLEMENTO .010'' Thk; Steel (Not shown) .010'' Thk
-
341TAZA; - bearing
-
351CUP ASSY.; CONE - bearing
-
361TUERCA; - adjusting, countershaft front bearing
-
371JUNTA; - countershaft front bearing cap
-
381TAPÓN; - countershaft front bearing
-
393X; HHCS AND LOCKWASHER - bearing cap
-
401EJE; ASSEMBLY - reverse idler
-
411X; PLUG - pipe, slotted headless
-
421LOCK ASSY; LOCK - reverse idler shaft
-
431PERNO Hex, 3/8'' - 16 x 5/8'', Gr 5, Full Thd; Reverse idler shaft lock Hex, 3/8''-16 x 5/8'', G5, Full Thd
-
441ARANDELA DE BLOQUEO Ext Tooth, 0.391'' ID x 0.682'' OD, STL, PLN; WASHER - Shakeproof lock, internal tooth (3/8'')
-
452COJINETE RODILLO CÓNICO; BEARING - needle, reverse idler
-
461SIN SERVICIO; GEAR - reverse idler
-
471PALANCA; - gear shift
-
481X; KNOB - gear shift lever
-
491X; COVER - dust, gear shift lever
-
501PASADOR; - stake, gear shift lever
-
511ANILLO DE RESORTE; SNAP RING - gear shift lever
-
521ARANDELA; - pivot, gear shift lever
-
531GUÍA DESLIZANTE; COVER AND GUIDE ASSEBLY - control
-
541PLACA; - guide, control cover
-
552REMACHE But Hd, 1/4'' x 7/8''; - button head, guide plate to control cover (1/4'' x 7/8'')
-
561JUNTA; - control cover
-
574PERNO Hex, 3/8'' - 16 x 7/8'', Gr 5, Full Thd;
-
584ARANDELA DE BLOQUEO 3/8'';
-
591VARILLA; - shift, first and reverse
-
605ARANDELA; - spacer, first and reverse shift fork
-
611PASADOR; - lock, first and reverse shift rod (Short)
-
621HORQUILLA HENIFICADO; FORK - shift, first and reverse
-
632RESORTE; - mesh lock, shift fork
-
642X; BALL - mesh lock, shift fork (3/8'' dia.) use 211-11
-
652BOLA 3/8'' Dia; - mesh lock, shift fork (.) 3/8'' Dia
-
661PASADOR; ROD - shift, second and third
-
671SIN SERVICIO; PIN - lock, second and third shift rod (Long)
-
684PERNO Hex, 9/16'' - 12 x 1'', Gr 5; HHCS - 9/16'' - 12 NC x 1''
-
691JUNTA; - transmission cover plate
-
701PLACA; - cover, transmission
-
7111PERNO Hex, 7/16'' - 14 x 1-1/4'', Gr 5, Full Thd;
-
11ARANDELA DE BLOQUEO 7/16''; used up to tractor S/N 3017412 (Use Loctite ''Grade CV'') (Not shown) 7/16''@@When reassembling transmission cover plate on tractors prior to S/N 3017412, discard lockwashers and apply Loctite ''Grade CV'' to mounting bolts.
-
722ANILLO DE CIERRE; - cork, final drive spacer to transmission case (Used with transmission case that has recess in faced surface and any spacer tubes with or without ''O''ring groove) See D27642 and D29309
-
732X; SEAL - ''O''ring, final drive spacer to transmission case (Used with transmission case that has solid faced surface and spacer tube with ''O''ring groove) See 32369 and D29309
-
73A2JUNTA; - final drive spacer to transmission case (Used with transmission case that has solid faced surface and spacer tube without ''O''ring groove) See 32369 and D27642
-
741SIN SERVICIO; SPACER - final drive, R.H. (Standard 48'' gauge tractor) has plain faced surface on transmission side (Original equipment) When stock is exhausted use 1 - D29728, 4 - 14-1228, 4 - 92-12, and 4 - 25-112
-
741ACUMULADOR; SPACER - final drive R.H. (42'' gauge tractor) has plain faced surface on transmission side (Original equipment) When stock is exhausted use 1 - D29788, 4 - 14-1228, 4 - 92-12, and 4 - 25-1112
-
741ASIENTO; SPACER - final drive, R.H. (42'' gauge tractor) Has plain faced surface on transmission side (Replacement) See 11977
-
741JUNTA TÓRICA; SPACER - final drive, R.H. (72'' gauge tractor) Has plain faced surface on transmission side (Original equipment) When stock is exhausted use 1 - D29794, 4 - 14-1228, 4 - 92-12, and 4 - 92-12, and 4 - 25-1112
-
741X; SPACER - final drie, R.H. (72'' gauge tractor) has plain faced surface on transmission side (Replacement) See 11974
-
751SIN SERVICIO; SPACER - final drive, L.H. (Standard 48'' gauge tractor) has plain faced surface on transmission side (Original equipment) When stock is exhausted use 1 - D29729, 4 - 14-1228, 4 - 92-12, and 4 - 25-1112
-
751PULLER; SPACER - final drive, L.H. (42'' gauge tractor) has plain faced surface on transmission side (Original equipment) When stock is exhausted use 1 - D29787, 4 -14-1228, 4 - 92-12, and 4 - 25-1112
-
751ACOPLAMIENTO; SPACER - final drive, L.H. (72'' gauge tractor) has plain faced surface, on transmission side (Original equipment) When stock is exhausted use 1 - D29795, 4 - 14-1228, 4 - 92-12, and 4 - 25-1112
-
751X; SPACER - final drive, L.H. (72'' gauge tractor) has plain faced surface on transmission side (Replacement) See 11975
-
7612PRISIONERO; - final drive spacer to transmission (9/16'' x 1'')
-
7712TUERCA DE BLOQUEO 9/16''-18, GB; NUT - lock (9/16'' - 18 NF)
-
788PERNO Hex, 5/8'' - 18 x 1-3/4'', Gr 5; (Used with original equipment spacers only) See 14-1228 Hex, 5/8''-18 x 1 3/4'', G5
-
8PERNO Hex, 3/4'' - 16 x 1-3/4'', Gr 5; HHCS - 3/4'' - 16 NF x 1-3/4'' (Used with replacement spacers only) See 14-1028
-
798ARANDELA DE BLOQUEO 5/8''; WASHER, LOCK, 5/8''
-
8ARANDELA DE BLOQUEO 3/4''; WASHER, LOCK, 3/4''
-
808TUERCA 5/8''-18, G5; - hex. (5/8'' - 18 NF)
-
8TUERCA 3/4''-16, G5; - hex. (3/4'' - 16 NF)
-
812X; SEAL - ''O''ring, final drive spacer outer flange
Select
Ref.
25Ctd
1Disponibilidad
N.º de pieza
40385Descripción
COJINETE 3.375'' OD x 0.9375''Img
Select
Ref.
31Ctd
1Disponibilidad
N.º de pieza
101-21250Descripción
ANILLO DE RESORTE #250, 2.673'', IntImg
Select
Ref.
43Ctd
1Disponibilidad
N.º de pieza
13-610Descripción
PERNO Hex, 3/8'' - 16 x 5/8'', Gr 5, Full ThdImg
Select
Ref.
44Ctd
1Disponibilidad
N.º de pieza
193-10Descripción
ARANDELA DE BLOQUEO Ext Tooth, 0.391'' ID x 0.682'' OD, STL, PLNImg
Select
Ref.
55Ctd
2Disponibilidad
N.º de pieza
45-414Descripción
REMACHE But Hd, 1/4'' x 7/8''Img
Select
Ref.
57Ctd
4Disponibilidad
N.º de pieza
13-614Descripción
PERNO Hex, 3/8'' - 16 x 7/8'', Gr 5, Full ThdImg
Select
Ref.
68Ctd
4Disponibilidad
N.º de pieza
13-916Descripción
PERNO Hex, 9/16'' - 12 x 1'', Gr 5Img
Select
Ref.
71Ctd
11Disponibilidad
N.º de pieza
13-720Descripción
PERNO Hex, 7/16'' - 14 x 1-1/4'', Gr 5, Full ThdImg
Select
Ref.
77Ctd
12Disponibilidad
N.º de pieza
131-675Descripción
TUERCA DE BLOQUEO 9/16''-18, GBImg
Select
Ref.
78Ctd
8Disponibilidad
N.º de pieza
14-1028Descripción
PERNO Hex, 5/8'' - 18 x 1-3/4'', Gr 5Img
Select
Ref.
Ctd
8Disponibilidad
N.º de pieza
14-1228Descripción
PERNO Hex, 3/4'' - 16 x 1-3/4'', Gr 5Img